Schedule Now

 

 

They are making a few good annotation regarding A Step-by-Step Guide to Installing a Bathtub as a whole in this great article down the page.

Mounting a bathtub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a new one is likewise a moderately tough task. If the old bathtub is conveniently accessible, the project can move easily; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new tub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. Make certain you have actually certified yourself for the task and are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to take into consideration employing one before you start. Possibilities are you might require an expert plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a new tub as well as do not need to change the setup of your previous supply of water pipelines.
Your devices and product checklist need to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

First of all, the sustaining frame provided with the bath must be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite troublesome due to the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Setting up the Bathtub

Making use of both wooden boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly settle it into its last placement.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer provided backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I'm certainly very interested by How to Install a Bathtub and I really hope you appreciated the new article. Enjoyed our review? Please share it. Let other people discover it. Thank-you for taking the time to read it.

Schedule Your Job Now